3m interconnect solutions division 6801 river place blvd. austin, tx 78726-9000 for technical, sales or ordering information call 800-225-5373 .100 .100 latch/ejector header 3 wall, straight & right angle, high temp option 18 ts-0771-02 sheet 1 of 4 military (with 3m's 3518 polarizing key ) and center bump polarization low profile optional ejector latches mounting holes for securing header to board three wall shroud provides design flexibility solder tail and wrap tail options optional polarizing posts available high temperature option date modified: october 19, 1999 physical insulation material: glass filled polyester (pbt) glass filled polyester (pct e high temp option) flammability: ul 94v-0 color: gray beige (high temp option) marking: 3m logo, part identification number and orientation triangle contact material: copper alloy plating underplate: 100 m [ 2.54 m m ] nickel e qq-n-290, class 2 wiping area: gold e mil-g-45204, type ii, grade c solder tails: 200 m [ 5.08 m m ] 60/40 tin lead e mil-p-81728 wrap tails: gold flash electrical current rating: 1 a insulation resistance: >1 10 9 w at 500 vdc withstanding voltage: 1000 vrms at sea level environmental temperature rating: 55 c to +105 c ul file no.: e68080
3m interconnect solutions division 6801 river place blvd. austin, tx 78726-9000 for technical, sales or ordering information call 800-225-5373 .100 .100 latch/ejector header 3 wall, straight & right angle, high temp option .424 .010 [ 10.77 ] .025 .002 sq typ [ 0.64 ] .573 .010 [ 14.55 ] -x0xx header with no ejector/latch -x5xx header with short ejector/latch for 3m sockets without strain relief -x6xx header with long ejector/latch for 3m sockets with strain relief -x4xx header with ejector only .08 [2.0] .97 ref [24.6] .37 ref [9.4] .46 ref [11.7] 1.07 ref [27.2] .42 ref [10.7] 1.07 ref [27.2] .08 [2.0] d .020 [0.51] .15 [3.8] .12 [3.0] position 1 .100 ref [2.54] .28 [7.1] .25 [6.4] .30 [7.6] position 1 orientation triangle .21 [5.3] .24 [6.1] .30 [7.6] f typ e .010 .049 ref [1.24] .100 ref [2.54] 2x .100 [2.54] (see note 2) a c .16 [4.1] .197 [5.00] .20 [5.1] .12 [3.0] notch c (see table 1 & note 1) notch b (see table 1) notch a (see table 1 & note1) b b section bb note: this ejector is a nickel plated zinc alloy casting. .100 ref [2.54] (right angle) .68 [17.3] .35 [8.9] .020 [0.51] a a f typ section aa (straight) e .010 .30 [7.6] .24 [6.1] .025 .002 sq typ [ 0.64 ] ts-0771-02 sheet 2 of 4 b 2x .100 [2.54] (see note 2) c l c l ayo ayo ? ?
3m interconnect solutions division 6801 river place blvd. austin, tx 78726-9000 for technical, sales or ordering information call 800-225-5373 .100 .100 latch/ejector header 3 wall, straight & right angle, high temp option table 1 pin 3m part dimensions polarization notches pn quantity 3m part number a b c d notches provided 10 3793 1.26 [32.1] 1.105 [28.07] .865 [21.97] .71 [18.0] b c 14 3314 1.46 [37.2] 1.305 [33.15] 1.065 [27.05] .91 [23.1] b c 16 3408 1.56 [39.7] 1.405 [35.69] 1.165 [29.59] 1.01 [25.6] a b c 20 3428 1.76 [44.8] 1.605 [40.77] 1.365 [34.67] 1.21 [30.7] a b c 26 3429 2.06 [52.4] 1.905 [48.39] 1.665 [42.29] 1.51 [38.3] a b c 34 3431 2.46 [62.6] 2.305 [58.55] 2.065 [52.45] 1.91 [48.5] a b c 40 3432 2.76 [70.2] 2.605 [66.17] 2.365 [60.07] 2.21 [56.1] a b c 50 3433 3.26 [82.9] 3.105 [78.87] 2.865 [72.77] 2.71 [68.8] a b c 60 3372 3.76 [95.6] 3.605 [91.57] 3.365 [85.47] 3.21 [81.5] a b c 64 3764 3.96 [100.7] 3.805 [96.65] 3.565 [90.55] 3.41 [86.6] a b c table 2 3m part number cttt i l d ii e pin cross section d ii g number suffix contact tail dimension e dimension f diagonals corner radii dimension g -1xx2 -2xx2 solder tail for .062 [1.57] thick pc board .112 [2.84] 0.0245 .0005 [0.622] 0.028 .001 [0.71] 0.0075 ref [0.191] .035 .003 [0.89] (see note 3) -1x03 -2x03 solder tail for .094 [2.39] to .125 [3.18] thick pc board .155 [3.94] 0.0245 .0005 [0.622] 0.028 .001 [0.71] 0.0075 ref [0.191] .035 .003 [0.89] -3x05 -4x05 wire wrap tail for up to 3 levels of wire wrap .61 ref [15.5] 0.0250 .002 [0.635] 0.035 .003 [0.90] 0.003 max [0.08] .045 .003 [1.14] c l .41 [10.4] max to edge of pcb for daisy chain .106 [2.69] or .116 [2.95] (see note 2) g dia .029 [0.74] .100 .003 [2.54] position 1 .232 [5.89] c recommended mounting hole pattern (right angle) .100 .003 [2.54] .106 [2.69] or .116 [2.95] (see note 2) g dia position 1 .100 .003 [2.54] .100 .003 [2.54] .060 [1.52] .300 [7.62] side to side stackability b recommended mounting hole pattern (straight) .352 [8.94] notes: 1. notches a & c will accomodate 3m polarizing keys (3m part #3518 or m3518). 2. accepts rear and front mounting hardware: rear entry: #4-24 thread cutting screw, 3m part #3341-5, .116 [2.95] dia mounting hole front entry: (prior to installation of latch on straight versions) #2-56 bolt and nut, 3m part #3341-6, .106 [2.69] dia mounting hole 3. the recommended pcb hole size for the kinked tail positions on the .112 solder tail connector is .035 .002. refer to ts-0972 for the positions kinked. inch [mm] .005 .1 .01 tolerance unless noted .0 .00 .000 inch [ ] dimensions for reference only ts-0771-02 sheet 3 of 4 ayo ayo c l
3m interconnect solutions division 6801 river place blvd. austin, tx 78726-9000 for technical, sales or ordering information call 800-225-5373 .100 .100 latch/ejector header 3 wall, straight & right angle, high temp option ordering information xxxxx-xxxx 3m part number (see table 1) shroud and pin configuration 1 = 3 wall, right angle solder tail 2 = 3 wall, straight solder tail 3 = 3 wall, right angle wrap post (not available on high temp version) 4 = 3 wall, straight wrap post latch/ejector system 0 = no latch/ejector 4 = roll pin ejectors (3m part # 3505-4) 5 = short, snap-in latch/ejectors, (3m part # 3505-30) 6 = long, snap-in latch/ejectors (3m part # 3505-31) 30 microinches gold plated product tail 02 = solder tail for .062 [1.57] thick board k2=kinked solder tails for .062 [1.57] thick board 03 =solder tails for .094 to .125 [2.39 to 3.18] thick board 05 = wrap posts for up to 3 levels of wire wrap (not available on high temp version) xxxxx-xxxxug shroud and pin configuration 1 = 3 wall, right angle solder tail 2 = 3 wall, straight solder tail latch/ejector system 0 = no latch/ejector 5 = short, snap in latch/ejectors (3m part # 3505-30) 6 = long, snap in latch/ejectors (3m part # 3505-31) 15 microinches gold plated product tail 02 = solder tail for .062 [1.57] thick board k2=kinked solder tails for .062 [1.57] thick board 03 =solder tails for .094 to .125 [2.39 to 3.18] thick board 3m part number (see table 1) plating suffix ug = 15 microinch gold ts-0771-02 sheet 4 of 4 blank = standard n = high temperature blank = standard n = high temperature
|
